Gap specs updated November 2026
- Wet treated pine goes down tight. Kiln dried pine gets 1/16 to 1/8 inch. Trex composite gets 3/16 inch in all weather.
- Composite needs end gaps too. Trex asks for 1/8 inch at butt joints and 1/4 inch at the house on days above 40 degrees.
- Under oaks that drop leaves, Trex allows a wider gap, up to 3/8 inch, so debris falls through.
Deck board spacing comes down to two kinds of boards. Wet pressure treated pine goes down butted tight and opens its own gap as it dries. Kiln dried pine, composite and PVC go down with the gap already set, because they won't shrink much more. On the 12 by 16 foot deck in our Cedar Park deck cost guide, that choice changes the board count from 27 to 26. Get it wrong and you end up with gaps wide enough to catch a heel, or boards that buckle in August.
How Far Apart Should Deck Boards Be?
The right gap depends on the board, and the maker of the board sets it. The table puts the main choices side by side. Every number comes from the maker or a lumber group, listed at the bottom.
| Board | Side gap at install | End gap at butt joints |
|---|---|---|
| Wet pressure treated pine | None. Butt the boards tight. | None for wood |
| Kiln dried after treatment (KDAT) pine | 1/16 to 1/8 inch | None for wood |
| Trex composite | 3/16 inch in all weather, up to 3/8 inch by choice | 1/8 inch above 40 degrees, 3/16 inch below |
| TimberTech PRO and EDGE composite | 1/8 to 7/32 inch, by fastener | Yes, set by the install day's temperature |
| TimberTech AZEK PVC | 1/8 to 1/4 inch, by fastener | None |
The wood numbers come from the people who treat and sell the lumber. Culpeper Wood's deck building tips say to butt heavy, wet boards tight and space light, dry KDAT boards at least 1/16 inch but no more than 1/8 inch. YellaWood's KDAT tips say to gap its kiln dried decking the width of an 8 penny nail, which it puts at 1/8 inch.
The composite numbers come from the makers. Trex's spacing guide gives 3/16 inch side to side for its boards in any weather. TimberTech's spacing guide gives a range for each of its lines that shifts with the fastener you use.

Do Pressure Treated Deck Boards Need a Gap?
Wet ones don't, at least not on day one. Pine fresh from treatment is full of water. As it dries in the Texas sun, each board gets narrower. TimberTech's guide says to install wet treated boards tight with no gap for exactly that reason. The gap shows up on its own.
The classic mistake is a nail gap in wet pine. You space the boards the way a video told you, the boards shrink, and the gap ends up far wider than you planned. That's a gap that traps acorns, swallows a dropped phone and catches the edge of a shoe.
Dry boards are the reverse. KDAT pine has already been dried at the mill after treatment, so it won't shrink much more. Butt those tight and they have nowhere to go when a wet spring makes them swell. Culpeper notes some expansion may occur, which is why its dry gap is a small one.
How Do I Know if My Boards Are Wet or Dry?
Read the tag first. Culpeper tells builders to check the lumber tag for "KDAT" or wet lumber before they start. Then pick one up. Culpeper's own test uses weight. A wet board is heavy and feels damp. A dry board is light. If the tag and the weight disagree, trust the tag.
Does Composite Decking Need a Gap at the Ends?
Yes, and this is where a lot of first composite decks go wrong. Wood barely grows along its length. Composite does, as it heats and cools. Trex asks for 1/8 inch where two board ends meet on days warmer than 40 degrees, and 3/16 inch on colder days. Where a board end meets something solid, like the house or a post, Trex wants 1/4 inch above 40 degrees and 1/2 inch below.
TimberTech goes further for its PRO and EDGE boards. The end gap is set by the outdoor temperature on install day, from a chart in its install guide. TimberTech also says to keep boards as cool as you can while you fasten them.
What That Means for a Cedar Park Install Day
Most Cedar Park install days land on the warm side of Trex's 40 degree line. The closest official weather station, Camp Mabry in Austin, has normal January lows in the low 40s and only about 12 days a year below freezing, per the National Weather Service climate summary for Austin. So most of the year you'll use Trex's warm numbers, 1/8 inch at the ends and 1/4 inch at the house.
Summer is the harder season. The same summary puts normal highs at 90 or above from May 26 to September 23, with upper 90s in early August. A board that sat in the sun all afternoon is already at its longest. Cut and fasten it then and it pulls back on a cool night, opening the end gaps. Keep the stack in shade and do the cutting in the morning.
A Wider Gap Under Cedar Park Oaks
Trex lets you widen its 3/16 inch gap to 3/8 inch in heavily wooded yards, so leaves and other debris fall through. That matters here. A lot of Cedar Park decks sit under live oaks, and our guide to building a deck around a live oak covers why so many owners keep them.
A wider gap has a cost you can count. The table runs the math for boards 5 1/2 inches wide across a 12 foot frame, the same size as our cost guide deck. Culpeper lists that 5 1/2 inch width as the actual size of a 6 inch board, and the widest it suggests for decking.
| Gap | Boards needed | Total open gap |
|---|---|---|
| Tight (wet pine) | 27 | 0 inches at install |
| 1/8 inch | 26 | 3 1/8 inches |
| 3/16 inch | 26 | 4 11/16 inches |
| 1/4 inch | 26 | 6 1/4 inches |
| 3/8 inch | 25 | 9 inches |
The count barely moves. What moves is how much open air you walk over. At 3/8 inch, close to 9 inches of a 12 foot deck is gap. That's fine for leaves and rain. It's less fine for chair legs and dog nails. Under a big oak, 1/4 inch is a fair middle for composite. Check that your board's maker allows it before you pick it, or the warranty may not cover you.
How Far Apart Should the Joists Be?
The gap between boards gets the attention, but the joists under them decide if the deck feels solid. Trex's joist guide calls for joists no more than 16 inches on center for its boards, and 12 inches if the boards run on a diagonal. On an old wood deck framed at 24 inches, Trex suggests adding a joist between each pair.
Wood allows a little more. The Southern Pine Council's deck guide rates 5/4 and 2x6 pine decking to span up to 24 inches on center, but notes many pros hold 5/4 boards to 16 inches to cut bounce. Culpeper puts the same limits plainly, 24 inches for 2x decking and 16 for 5/4. Diagonal pine decking gets 16 inch joists.
If you plan to swap wood boards for composite decking, measure the joists first. A frame built for wood boards at 24 inches is too wide for composite until you add joists.
How Do I Keep the Gap Even Down the Whole Deck?
Use a spacer, not your eye. Plastic deck spacers come in set sizes, and a nail of the right width works on wood. Trex's hidden clips set a 1/4 inch gap for you, which is one reason many builders like them.
- Snap a chalk line every few rows to check that the boards stay straight.
- Clamp or pry a bowed board into line before you fasten it.
- Measure to the far edge when you're about eight boards out, so the last one isn't a thin sliver.
- Pre-drill wood ends, since Culpeper says to drill any time a screw is within a board's width of the end.
- Lay boards bark side up, which the Southern Pine Council says helps reduce splits and cupping.
A wood deck built with tight wet boards should open up gaps as it dries, and that's normal. We'll tell you which boards are on your deck, what gap they need and whether your joists can carry them. Ask for a free estimate.
Move Cedar Park Deck Builders up in your Google results
Source Material
| What we cited | Where it came from |
|---|---|
| Composite side gaps, end gaps and house gaps by temperature, wider gaps in wooded yards, hidden clip gap | Trex, How to Easily Space Deck Boards, December 2024 |
| Wet and dry wood gaps, composite and PVC gaps by line, keeping boards cool | TimberTech, Deck Board Spacing by Material, November 2021 |
| Wet boards tight, KDAT gap of 1/16 to 1/8 inch, tag and weight check, 6 inch board limit, joist limits, pre-drilling | Culpeper Wood Preservers, Deck Building Tips, 2025 |
| KDAT decking gapped the width of an 8 penny nail | YellaWood, KDAT Tips |
| Joist spacing for composite, diagonal boards and 24 inch frames | Trex, How to Space and Install Deck Joists |
| Pine decking spans, diagonal joists, bark side up | Southern Pine Council, Building a Southern Pine Deck |
| January lows, days below freezing, summer highs | National Weather Service Austin and San Antonio, Austin Climate Summary |
| Board count for a 12 by 16 deck | Our deck cost guide, which names the store and the day we checked |